KSh 22,600.00 Ex-VAT


Morningstar PS-30M Charge Controller 30A 12-24V

Morningstar PS-30M Charge Controller 30A 12-24V is commonly used for small to medium off-grid and other battery systems, such as backup power supplies. It can be used for any 12 or 24-volt battery system. It will handle up to 30 amps from the solar panels – about 500 watts of a panel at 12 volts, 1000 watts at 24 volts. Morningstar’s series switching provides many advantages compared to shunt controllers. Series regulation reduces FET heating and lowers voltage stress on the power FETs. A series configuration also improves protection against lightning surges and reduces switching noise. The series design improves charging accuracy. In PWM, series switching becomes self-correcting for temperature and system voltage drops. Maybe paralleled up to 300 amps.

Morningstar PS-30M Charge Controller 30A 12-24V is the world’s leading mid-range solar controller for both professional and consumer applications. This third-generation ProStar (PS-30) provides the following:

  • Adds new features and protections using highly advanced technology
  • Provides longer battery life and improved system performance
  • Sets new standards for reliability and self-diagnostics

Morningstar PS-30M Charge Controller 30A 12-24V Features


  • Versions available: 15 or 30 amp 12 / 24 or 48 volts negative or positive ground
  • Estimated 15-year life
  • PWM series battery charging (not shunt)
  • 3-position battery select: gel, sealed, or flooded
  • Very accurate control and measurement
  • Jumper to eliminate telecom noise
  • Parallel for up to 300 amps
  • Temperature compensation
  • Tropicalization: conformal coating, stainless steel fasteners & anodized aluminum heat sink
  • No switching or measurement in the grounded leg
  • 100% solid state
  • Very low voltage drops
  • Current compensated low voltage disconnect (LVD)
  • LEDs indicate the system status and various faults
  • Capable of 25% overloads
  • Remote battery voltage sense terminals


PS-15 PS-30 PS15M-48V
Rated Solar Current 15 Amps 30 Amps 15 Amps
Rated Load Current 15A 30A 15A
System Voltage 12/24V 12/24V 48V
Temp. Comp. (mV/°C)* – 30mV – 60mV – 120mV
Accuracy 40mV 60mV 80mV
Min. voltage to operate 8V 8V 15V
Self-consumption 22mA 25mA 28mA
LVD current coefficient** – 20mV – 40mV – 80mV
Charge algorithm PWM, constant voltage
Operating temperature – 40°C to + 60°C

Detailed Description


  • Short-circuit — solar and load
  • Overload — solar and load
  • Reverse polarity
  • Reverse current at night
  • High voltage disconnect
  • High-temperature disconnect
  • Lightning and transient surge protection
  • Loads protected from voltage spikes
  • Automatic recovery with all protections


  • Night Disconnect: The solar array automatically disconnects at night to prevent reverse current leakage from the battery.
  • Battery Sense: Good battery performance requires accurate charging. Voltage drops in the battery power cables can distort the battery charging. The Sense wires eliminate the voltage drops for optimized charging.
  • Temperature Compensation: Four control setpoints (25°C references) are compensated for temperature (PWM regulation, float, equalization, high voltage disconnect). The charging is compensated by –5 mV/°C /cell (–30mV/°C for a 12V battery). Compensation is limited to minus 30°C.
  • Remote Temperature Probe: An optional probe is available to measure temperature at a location away from the controller. This requires soldering 2 wires to the ProStar PCB.


  • Digital meters precision 3-digit digital meter will continuously display battery voltage, solar current, and load current. The meter automatically scrolls through these 3 displays. The 3 red LEDs will indicate which parameter is being displayed. The digital meter will operate from –30°C to +85°C. The values displayed are calibrated electronically in production and are accurate to within a few percent. Please note, however, that if the Battery Sense is not connected, the voltage displayed will be in error by the voltage drops in the battery wires.
    • Highly accurate voltage and current display
    • Low self-consumption (1 mA)
    • Includes manual disconnect button
    • Displays 5 different protection functions and disconnect conditions
    • Self-diagnostics (self-test) provides a comprehensive test of the ProStar —
      • Displays 9 different controller status parameters, including temperature
      • Displays detected faults
  • Positive ground
  • Remote temperature probe optional remote temperature probe can be soldered to the ProStar assembly at any time. The standard cable length is 25 ft (7.6 m), and this can easily be extended to 100 ft (30 m) or longer. The 2 probe wires are soldered to the main board assembly between the temperature sensor and the green LED, at “J12”.

Based on 0 reviews

0.00 Overall
Be the first to review “Morningstar PS-30M Charge Controller 30A 12-24V”

Your email address will not be published. Required fields are marked *

Write a review


There are no reviews yet.

Close My Cart
Close Recently Viewed